Welcome to Nanolia information

NanoliaTEC  for Vehicles formulated by RVS Technology®

Reduce emissions and cut fuel costs – an “Engine Rebuild in a Bottle”

NanoliaTEC is an exciting new “smart coating” formulation that enables almost any machine to operate more efficiently, while reducing fuel costs by around 11% and emissions by up to 60%.  Based on the latest nano-coating technology the product - which is simply added to engine or gearbox oil - is a low cost way to reduce the cost of operating your vehicle. It is equally effective from the smallest motorbike to the largest bus, lorry or locomotive. One application is good for 100,000 km - even if the oil is changed many times in that period. And after 100,000 km, it can be simply reapplied to further the vehicle's life. It’s like an engine or gearbox rebuild in a bottle.

NanoliaTEC - which is not classed as a fuel or oil additive - is a nano coating that actually prevents engine metal wear so that gears, pistons and bearings become almost maintenance free with an extended service life. In addition to this preventive use, it can also be used to repair worn parts, restoring them to their former quality and efficiency.

Environmentally Positive

 NanoliaTEC “smart coatings” are amazingly easy to apply and have a major positive impact for vehicle owners and fleet operators, helping cut costs while supporting sustainability and efficiency and contributing to cleaner air.

• Longer lasting engines / vehicle gears, pistons and bearings
• Fuel Efficiency: around 11% savings on fuel
• Emissions reductions (on average 50-60%)
• Optimization of engine power
• Improvement of cold-start properties
• Optimization of oil pressure
• Optimization of cylinder compression
• Reduction of engine noise and vibrations
• Reduction of CO₂-, CO-, HC-, NO_x- and diesel soot exhaust
• Emergency running properties without oil

How does it work?

Lubricants work by creating a protective film that avoids direct contact of the metallic surfaces. However, lubricants are not able to protect the metal surfaces under all conditions or permanently. This new nano coating technology works differently. It actually modifies the surface texture of frictional metal parts and creates a new, smooth metal silicate coating. This metal silicate coating reduces friction and increases efficiency, especially in older engines and gearboxes. Due to optimisation of compression pressure in engines, oil- and fuel consumption and emissions of exhaust gases such as COâ‚‚ are reduced.

The synthesised metal silicate compound only has to be added to the original lubricant to be carried to the affected areas of the engine or gear box. In the abrasion area, the metal silicates react due to high temperature and/or high partial pressure and conjoin with the metal surfaces, filling the smallest corrugations, pores or micro cracks in the metal surface, forming an extremely smooth and solid metal silicate layer. The treated metal silicate surfaces have a much lower friction coefficient and allow for a better and faster build-up of a lubricating film. At the top end of the scale, the effect on wind turbine gearboxes, for example, is well documented and significant in terms not only of extended gearbox life but also increased power generation.

Application Instructions:

Follow the instructions supplied with the product. In principle, select the correct package for your engine capacity or oil tank size. Immediately after an oil and filter change, run the engine until warm then add half the contents of bottle to the engine oil filler. The remainder should be added after 300km. The application is complete after 2000km and will last for around 100,000km.

Handling and Transport, special requirements:

Check!

Availability:

Bottles and packs of various sizes:

Storage:

Check! The product may be stored for at least XX months in its original packing. Protect from frost and direct sunlight.

Disposal:

Check! Empty containers can be disposed of with household waste. Containers with remaining contents must be disposed as hazardous waste in compliance with local regulations.

Safety/Protection Measures:

Check! When using this product please take note of these instructions. The use of chemical preparations should only take place when the safety measures are observed and should always take place out of the reach of children. If the skin is exposed to the product, immediately remove contaminated clothes and wash the affected area with lukewarm water and soap. If the eyes are exposed, flush with copious amounts of cold water, ensuring that the eyelids are also flushed by moving the eyes to extreme positions. If irritation persists, consult a doctor. If ingested, flush the mouth with cold water, but do not induce vomiting. Consult a doctor immediately. In case of fire, any kind of extinguishing material may be used except water. The technical information given here is according to the latest technical knowledge and compiled from our own experience. In view of the many uses possible with this product, it is the user’s responsibility as to how they act with regard to safety in any given situation whilst using this product. As the use of this product takes place out of our jurisdiction we cannot be held responsible for any accidents or safety issues that may arise under any circumstances, though we have endeavoured to provide adequate safety and protection instructions. We cannot be held responsible for any misuse of this product. In the event of a new version of this information becoming available the information here is no longer valid.

Updated: 02/08/2010 21:52             E&OE