Welcome to Nanolia information

Buy now More information

 

Nanolia Stone Protect

Nanolia Stone Protect is a new building material based on innovative Nanolia silicate technology. It reinforces stone, masonry and concrete by closing the pores and protecting the surface with an extremely high resistance to chemical attack and abrasive conditions. Treated surfaces are waterproof but remain breathable.

The treated substrates are waterproof but remain breathable. Nanolia Stone Protect penetrates 2mm - 3mm below the surface, reacting with the cement components to forming a hard silicate structure.

Suitable for all types of absorbent mineral substrates such as concrete, paving stones, floor screed, sand and cementitious materials,  Nanolia Stone Protect is odourless, free from solvents and easy to use. The coating dries out over 10-15 year and is not removable. Suitable for indoor and outdoor use, it performs best in cementitious products with high calcium content.  It provides extra protection outdoors where freeze-thaw cycles may be a significant issue. In particular, because it is an impregnating, hydro-phobic sealer it also protects porous building materials such as brick, tiles, concrete and paving against efflorescence.

Features at a glance:

  • Single component, aqueous solution
  • Waterproofing
  • Prevents efflorescence and weathering as well as algae
  • Prevents the penetration of pollutants into the concrete
  • Optically neutral
  • Hydrophobic beading
  • Protection from frost, snow and ice (resistant to commonly used de-icers)
  • Highly abrasion resistant
  • Operating temperature from -30 ° C to 700°C
  • Increases the compressive and flexural strength of cementitious materials
  • Environmentally-sound - manufactured from inorganic materials
  • Good penetration through low viscosity

Compared to Nanolia Marble Protect:

  •  Higher resistance to chemicals (especially acids)
  •  Penetrates deeper into the substrates because of lower viscosity
  •  Seals against water pressure to 0.3 bar
  •  Suitable for less absorbent surfaces
  •  Requires calcium in the substrate for best results
  •  Only hydrophobic, not oleophobic
  •  Does not form a surface film
  •  No visible change in the appearance of the treated surfaces

Applications:

  •  Protection of old and new concrete floors to all kinds of corrosive liquids such as salt water, water, wastewater, sulfuric acid, etc ...
  •  Protection of concrete walls in tunnel s
  •  Prevent flaking of the surface by alternate freezing and thawing
  •  Suitable for garages, driveways, roof terraces, flat roofs, etc ...
  •  Protection of concrete floors in animal enclosures against bacteria, mould and fungi
  •  Crack-bridging against water penetration
  •  Bonding of porous surfaces
  •  Primer to prevent paint chipping
  •  Waterproofing cement joints in sanitary and industrial areas
  •  Protection and repair of pipelines and water storage containers
  •  Sealing of the outer surfaces of basements and walls
  •  For all areas with high chemical and mechanical stress

Application Instructions:

Always test a small sample to ensure that the desired result is achieved before proceeding with the main project. If in doubt, do not proceed.

Application temperatures between +5 ° C and 50 ° C. Maximum humidity 85%. The surface must be dry, clean and free from grease and oil. Dust and loose residues of plaster and cement must be removed thoroughly. Apply in two coats at an interval of 10-15 minutes to complete saturation. Test first to avoid puddling. The job can be done by brush, roller or sprayer.

The surfaces should be protected for 24 hours after treatment before exposure to rain or water condensation. Within this period avoid close proximity or contact. The drying time can be accelerated by ventilation.

Any rain or water falling on the surface in the first 7 days after application should be removed immediately. Chemical resistance increases progressively over the first 4 weeks. Avoid the use of  alkaline floor cleaners during the first 4 weeks. Adjacent mineral surfaces such as glass or tiles should be protected against splashes. Avoid contact with aluminium. Wash off any impurities immediately with water. Application equipment can be cleaned with water.

If possible, use undiluted. For highly absorbent surfaces it may be advisable to dilute the solution with water up to a factor of 1:1. Details of processing are highly dependent on the coated surface. We are happy to advise you on this issue.

Coverage:

Depending on absorbency of the surface, consumption is about 100gr.-350 gr / m².

Marking / Transport:

Non-dangerous goods according to RID, ADR, ADNR, IMDG, IATA-DGR.

Package sizes:

1 kg bottle, 10 kg cans, 30 kg canister. Other container sizes may be possible depending on the transport route and method of transportation.

Storage:

At least 24 months in cool storage in the original sealed containers. Protect from frost.

Disposal (German regulations):

Empty containers can be disposed of with household waste. Containers with remaining contents must be disposed as hazardous waste in compliance with local regulations.

Safety/Protection Measures:

When using this product please take note of these instructions. We wish to make it clear that the use of chemical preparations should only take place when the safety measures are observed and always out of the reach of children. The technical information given here is according to the latest technical knowledge and compiled from our own experience. In view of the many uses possible with this product it is therefore the responsibility of the user to act according to the given situation in respect of safety - that is to say the user acts on their own responsibility in any given situation when using this product. As the use of this product takes place out of our jurisdiction we have set out safety and protection measures, but we cannot be held responsible in any circumstances. For any misuse of the product we cannot be held responsible. In the event of a new version of this information becoming available – the information set out here is no longer valid.

Updated: 03/09/2010 16:59             E&OE

 

Example Application