Welcome to Nanolia information

Nanolia Marble Protect

Impregnation and sealing for protection of absorbent mineral substrates against the effects of pollution and damage from oil, grease, dirt and water.  Usable on all types of absorbent mineral surfaces such as concrete, plaster, marble, paving stone, screed and cementitious materials, the coating lasts for up to 15 years and is not removable. Suitable for indoor and outdoor use, Nanolia Marble Protect is free of solvents and easy to use.

Features at a glance:

·         Single component, environmentally friendly, aqueous solution

·         Seals against the ingress of salt water, sewage, chemicals, fats and oils

·         Increases surface strength of concrete and screed

·         Reduces abrasion

·         Hydrophobic and oleophobic beading

·         Stain protection – proof against coffee, cola, red wine, etc ...

·         Closes the pores and prevents the penetration of pollutants into the concrete

·         Prevents efflorescence and weathering

·         Reduction of algae and moss

·         Protection from frost, snow and ice

·         Optically nearly neutral

·         Abrasion resistant

·         Excellent penetration

Compared to Nanolia Stone Protect

·          Less resistant to acid

·          Lower penetration, higher viscosity

·          Resists water ingress at 0.5 bar; depending on substrate to a maximum of  1.0 bar.

·          Suitable for very absorbant substrates

·          Requires no calcium in the base substrate

·          Hydrophobic and oleophobic

·          Forms a light film

·          Easily applied to highly absorbant substrates

Applications:

·         Dirt and stain protection for almost all mineral surfaces, both indoors and out

·         Protection of old and new concrete floors against all types of aggressive fluids such as salt water, wastewater,  oils, etc ...

·          Protection of concrete walls in tunnels

·          Prevent flaking of the surface by alternate freezing and thawing

·          Suitable for garages, driveways, roof terraces, flat roofs, etc ...

·          Protection of concrete floors in animal enclosures against bacteria, mould and fungi

·          Protects against water penetration at cracks

·          Waterproofing cement joints in sanitary and industrial areas

·          Protection and repair of pipelines and water storage containers

·          Sealing of the outer surfaces of basements and walls

·          For all areas with high chemical and mechanical stress

Application Instructions:

Always test a small sample to ensure that the desired result is achieved before proceeding with the main project. If in doubt, do not proceed.

Use undiluted. Application temperature between +5 ° C and 50 ° C. Maximum humidity 95%. The surface must be dry, clean and free from grease and oil. Dust and loose residues Plaster / Cement / Sand / chalk must be removed thoroughly.

Apply by brush, roller or spray. Depending on absorbency apply in one or two operations approx 10-15 minutes apart to complete saturation. Test first to avoid puddling. The surface should be protected for 24 hours after treatment before exposure to rain or water condensation. Within this period avoid close proximity or contact. The drying time can be accelerated by ventilation.

Any rain or water falling on the surface in the first 7 days after application should be removed immediately. Chemical resistance increases progressively over the first 4 weeks. Avoid the use of  alkaline floor cleaners during the first 4 weeks. Adjacent mineral surfaces such as glass or tiles should be protected against splashes. Avoid contact with aluminium. Wash off any impurities immediately with water. Application equipment can be cleaned with water.

Wear and tear or partial damage can be repaired by additional local application.

Details of the application process are highly dependent on the coated surface. We are happy to advise you on this issue.

Coverage:

Depending on absorbency of the surface, approx 100gr.-350 gr / m².

Marking / Transport:

Non-dangerous goods according to RID, ADR, ADNR, IMDG, IATA-DGR.

Container sizes:

1 kg bottle, 10 kg cans, 30 kg canister. Other container sizes may be possible depending on the transport route and method of transportation.

Storage:

At least 24 months in cool storage in sealed original containers. Protect from frost.

Disposal

Empty containers can be disposed of with household waste. Containers with remaining contents must be disposed as hazardous waste in compliance with local regulations.

Safety/Protection Measures:

When using this product please take note of the instructions on this leaflet. We wish to make it clear that the use of chemical preparations should only take place when the safety measures are observed and always out of the reach of children. The technical information given here is according to the latest technical knowledge and compiled from our own experience. In view of the many uses possible with this product it is therefore the responsibility of the user to act according to the given situation in respect of safety - that is to say the user acts on their own responsibility in any given situation when using this product. As the use of this product takes place out of our jurisdiction we have set out safety and protection measures, but we cannot be held responsible in any circumstances. For any misuse of the product we cannot be held responsible. In the event of a new version of this information becoming available – the information set out here is no longer valid.